.rtorrent.rc: Adding rtorrent configuration file

1 files changed, 106 insertions, 0 deletions

diff --git a/.rtorrent.rc b/.rtorrent.rc
new file mode 100644
index 0000000..bd60122
--- /dev/null
+++ b/.rtorrent.rc
@@ -0,0 +1,106 @@
+# This is an example resource file for rTorrent. Copy to
+# ~/.rtorrent.rc and enable/modify the options as needed. Remember to
+# uncomment the options you wish to enable.
+
+# Maximum and minimum number of peers to connect to per torrent.
+min_peers = 40
+max_peers = 100
+
+# Same as above but for seeding completed torrents (-1 = same as downloading)
+min_peers_seed = 5
+max_peers_seed = 20
+
+# Maximum number of simultanious uploads per torrent.
+max_uploads = 5
+
+# Global upload and download rate in KiB. "0" for unlimited.
+download_rate = 0
+upload_rate = 30
+
+# Default directory to save the downloaded torrents.
+directory = /home/dave/Downloads/rtorrent/tmp
+
+# Default session directory. Make sure you don't run multiple instance
+# of rtorrent using the same session directory. Perhaps using a
+# relative path?
+session = /home/dave/Downloads/rtorrent/session
+
+# Watch a directory for new torrents, and stop those that have been
+# deleted.
+
+#schedule = watch_directory,5,5,load_start=./watch/\*.torrent
+#schedule = untied_directory,5,5,stop_untied=
+
+schedule = watch_directory_all,10,10,"load_start=/home/dave/Downloads/*.torrent,d.set_custom1=/home/dave/Downloads/"
+
+# On completion, move the torrent to the directory from custom1.
+system.method.set_key = event.download.finished,move_complete,"d.set_directory=$d.get_custom1=;execute=mv,-u,$d.get_base_path=,$d.get_custom1="
+#on_finished = move_complete,"d.set_directory=$d.get_custom1= ;execute=mv,-u,$d.get_base_path=,$d.get_custom1="
+
+# Close torrents when diskspace is low.
+schedule = low_diskspace,5,60,close_low_diskspace=100M
+
+# Stop torrents when reaching upload ratio in percent,
+# when also reaching total upload in bytes, or when
+# reaching final upload ratio in percent.
+# example: stop at ratio 2.0 with at least 200 MB uploaded, or else ratio 20.0
+#schedule = ratio,60,60,"stop_on_ratio=200,200M,2000"
+
+# Port range to use for listening.
+port_range = 6890-6892
+
+# Start opening ports at a random position within the port range.
+port_random = no
+
+# Check hash for finished torrents. Might be usefull until the bug is
+# fixed that causes lack of diskspace not to be properly reported.
+check_hash = yes
+
+# Set whetever the client should try to connect to UDP trackers.
+use_udp_trackers = yes
+
+# Alternative calls to bind and ip that should handle dynamic ip's.
+#schedule = ip_tick,0,1800,ip=rakshasa
+#schedule = bind_tick,0,1800,bind=rakshasa
+
+# Encryption options, set to none (default) or any combination of the following:
+# allow_incoming, try_outgoing, require, require_RC4, enable_retry, prefer_plaintext
+#
+# The example value allows incoming encrypted connections, starts unencrypted
+# outgoing connections but retries with encryption if they fail, preferring
+# plaintext to RC4 encryption after the encrypted handshake
+#
+encryption = allow_incoming,enable_retry,prefer_plaintext
+
+# Enable DHT support for trackerless torrents or when all trackers are down.
+# May be set to "disable" (completely disable DHT), "off" (do not start DHT),
+# "auto" (start and stop DHT as needed), or "on" (start DHT immediately).
+# The default is "off". For DHT to work, a session directory must be defined.
+# 
+dht = auto
+
+# UDP port to use for DHT. 
+# 
+dht_port = 6893
+
+# Enable peer exchange (for torrents not marked private)
+#
+peer_exchange = yes
+
+#
+# Do not modify the following parameters unless you know what you're doing.
+#
+
+# Hash read-ahead controls how many MB to request the kernel to read
+# ahead. If the value is too low the disk may not be fully utilized,
+# while if too high the kernel might not be able to keep the read
+# pages in memory thus end up trashing.
+#hash_read_ahead = 10
+
+# Interval between attempts to check the hash, in milliseconds.
+#hash_interval = 100
+
+# Number of attempts to check the hash while using the mincore status,
+# before forcing. Overworked systems might need lower values to get a
+# decent hash checking rate.
+#hash_max_tries = 10