diff options
| -rw-r--r-- | .rtorrent.rc | 106 |
1 files changed, 106 insertions, 0 deletions
diff --git a/.rtorrent.rc b/.rtorrent.rc new file mode 100644 index 0000000..bd60122 --- /dev/null +++ b/.rtorrent.rc @@ -0,0 +1,106 @@ +# This is an example resource file for rTorrent. Copy to +# ~/.rtorrent.rc and enable/modify the options as needed. Remember to +# uncomment the options you wish to enable. + +# Maximum and minimum number of peers to connect to per torrent. +min_peers = 40 +max_peers = 100 + +# Same as above but for seeding completed torrents (-1 = same as downloading) +min_peers_seed = 5 +max_peers_seed = 20 + +# Maximum number of simultanious uploads per torrent. +max_uploads = 5 + +# Global upload and download rate in KiB. "0" for unlimited. +download_rate = 0 +upload_rate = 30 + +# Default directory to save the downloaded torrents. +directory = /home/dave/Downloads/rtorrent/tmp + +# Default session directory. Make sure you don't run multiple instance +# of rtorrent using the same session directory. Perhaps using a +# relative path? +session = /home/dave/Downloads/rtorrent/session + +# Watch a directory for new torrents, and stop those that have been +# deleted. + +#schedule = watch_directory,5,5,load_start=./watch/\*.torrent +#schedule = untied_directory,5,5,stop_untied= + +schedule = watch_directory_all,10,10,"load_start=/home/dave/Downloads/*.torrent,d.set_custom1=/home/dave/Downloads/" + +# On completion, move the torrent to the directory from custom1. +system.method.set_key = event.download.finished,move_complete,"d.set_directory=$d.get_custom1=;execute=mv,-u,$d.get_base_path=,$d.get_custom1=" +#on_finished = move_complete,"d.set_directory=$d.get_custom1= ;execute=mv,-u,$d.get_base_path=,$d.get_custom1=" + +# Close torrents when diskspace is low. +schedule = low_diskspace,5,60,close_low_diskspace=100M + +# Stop torrents when reaching upload ratio in percent, +# when also reaching total upload in bytes, or when +# reaching final upload ratio in percent. +# example: stop at ratio 2.0 with at least 200 MB uploaded, or else ratio 20.0 +#schedule = ratio,60,60,"stop_on_ratio=200,200M,2000" + +# Port range to use for listening. +port_range = 6890-6892 + +# Start opening ports at a random position within the port range. +port_random = no + +# Check hash for finished torrents. Might be usefull until the bug is +# fixed that causes lack of diskspace not to be properly reported. +check_hash = yes + +# Set whetever the client should try to connect to UDP trackers. +use_udp_trackers = yes + +# Alternative calls to bind and ip that should handle dynamic ip's. +#schedule = ip_tick,0,1800,ip=rakshasa +#schedule = bind_tick,0,1800,bind=rakshasa + +# Encryption options, set to none (default) or any combination of the following: +# allow_incoming, try_outgoing, require, require_RC4, enable_retry, prefer_plaintext +# +# The example value allows incoming encrypted connections, starts unencrypted +# outgoing connections but retries with encryption if they fail, preferring +# plaintext to RC4 encryption after the encrypted handshake +# +encryption = allow_incoming,enable_retry,prefer_plaintext + +# Enable DHT support for trackerless torrents or when all trackers are down. +# May be set to "disable" (completely disable DHT), "off" (do not start DHT), +# "auto" (start and stop DHT as needed), or "on" (start DHT immediately). +# The default is "off". For DHT to work, a session directory must be defined. +# +dht = auto + +# UDP port to use for DHT. +# +dht_port = 6893 + +# Enable peer exchange (for torrents not marked private) +# +peer_exchange = yes + +# +# Do not modify the following parameters unless you know what you're doing. +# + +# Hash read-ahead controls how many MB to request the kernel to read +# ahead. If the value is too low the disk may not be fully utilized, +# while if too high the kernel might not be able to keep the read +# pages in memory thus end up trashing. +#hash_read_ahead = 10 + +# Interval between attempts to check the hash, in milliseconds. +#hash_interval = 100 + +# Number of attempts to check the hash while using the mincore status, +# before forcing. Overworked systems might need lower values to get a +# decent hash checking rate. +#hash_max_tries = 10 |